Edge-Core ES3528M-PoE Guide d'installation Page 479
- Page / 694
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
General Security Measures
4-151
4
show network-access
Use this command to display the MAC authentication settings for port interfaces.
Syntax
show network-access [interface interface]
• interface - Specifies a port interface.
• ethernet unit/port
- unit - This is unit 1.
- port - Port number. (Range: 1-28)
Default Setting
Displays the settings for all interfaces.
Command Mode
Privileged Exec
Example
show network-access mac-address-table
Use this command to display secure MAC address table entries.
Syntax
show network-access mac-address-table [static | dynamic]
[address mac-address [mask]] [interface interface] [sort {address |
interface}]
• static - Specifies static address entries.
• dynamic - Specifies dynamic address entries.
• mac-address - Specifies a MAC address entry. (Format: xx-xx-xx-xx-xx-xx)
• mask - Specifies a MAC address bit mask for filtering displayed addresses.
• interface - Specifies a port interface.
• ethernet unit/port
- unit - This is unit 1.
- port - Port number. (Range: 1-28)
• sort - Sorts displayed entries by either MAC address or interface.
Console#show network-access interface ethernet 1/1
Global secure port information
Reauthentication Time : 1800
--------------------------------------------------
--------------------------------------------------
Port : 1/1
MAC Authentication : Disabled
MAC Authentication Intrusion action : Block traffic
MAC Authentication Maximum MAC Counts : 1024
Maximum MAC Counts : 2048
Dynamic VLAN Assignment : Enabled
Guest VLAN : Disabled
Console#
- Powered by Accton 1
- Fast Ethernet Switch 3
- ES3528M-PoE 4
- E112008/ST-R01 F1.1.0.11 4
- 149100041600A 4
- About This Guide 5
- Contents 24
- Chapter 1: Introduction 33
- Introduction 34
- System Defaults 38
- Connecting to the Switch 41
- Required Connections 42
- Basic Configuration 43
- Setting Passwords 44
- Setting an IP Address 44
- Dynamic Configuration 45
- Initial Configuration 46
- Trap Receivers 47
- Managing System Files 48
- Saving Configuration Settings 49
- Using the Web Interface 51
- Home Page 52
- Panel Display 53
- Main Menu 54
- Manual Configuration 68
- Using DHCP/BOOTP 69
- Enabling Jumbo Frames 70
- Managing Firmware 71
- Console Port Settings 75
- Telnet Settings 77
- Configuring Event Logging 79
- Remote Log Configuration 80
- Displaying Log Messages 82
- Resetting the System 84
- Setting the System Clock 85
- Setting the Time Manually 86
- Configuring SNTP 86
- Configuring NTP 87
- Setting the Time Zone 89
- Enabling SNMP Agent Status 91
- Setting the Local Engine ID 96
- Specifying a Remote Engine ID 97
- Configuring SNMPv3 Users 98
- Configuring the Switch 100
- Configuring SNMPv3 Groups 102
- Setting SNMPv3 Views 105
- User Authentication 107
- Configuring User Accounts 108
- Configuring Encryption Keys 114
- Configuring AAA Accounting 118
- AAA Accounting Update 120
- AAA Accounting Exec Settings 123
- AAA Accounting Summary 123
- Authorization Settings 125
- Authorization EXEC Settings 126
- Authorization Summary 127
- Configuring HTTPS 128
- Configuring the Secure Shell 130
- Generating the Host Key Pair 133
- Importing User Public Keys 135
- Configuring the SSH Server 137
- Displaying 802.1X Statistics 144
- General Security Measures 147
- Configuring Port Security 148
- Web Authentication 149
- Access Control Lists 158
- Configuring a Standard IP ACL 159
- Configuring a MAC ACL 163
- DHCP Snooping 165
- Configuring DHCP Snooping 167
- IP Source Guard 172
- Console# 176
- Port Configuration 177
- Creating Trunk Groups 183
- Displaying LACP Port Counters 191
- Configuring Port Mirroring 198
- Configuring Rate Limits 199
- Showing Port Statistics 200
- Power Over Ethernet Settings 204
- Switch Power Status 205
- Setting a Switch Power Budget 206
- Displaying Port Power Status 206
- Configuring Port PoE Power 207
- Address Table Settings 209
- Displaying the Address Table 210
- Changing the Aging Time 211
- Displaying Global Settings 215
- Configuring Global Settings 218
- Displaying Interface Settings 222
- VLAN Configuration 234
- Assigning Ports to VLANs 235
- Displaying Current VLANs 239
- Creating VLANs 240
- Traffic Segmentation 253
- Private VLANs 256
- Configuring Private VLANs 257
- Associating VLANs 258
- Protocol VLANs 261
- 65536, and 264
- 65536 264
- Transmission Interval 265
- Link Layer Discovery Protocol 267
- Displaying Device Statistics 275
- Layer 2 Queue Settings 278
- Figure 3-131 Traffic Classes 281
- Selecting the Queue Mode 282
- Layer 3/4 Priority Settings 284
- Mapping DSCP Priority 285
- Quality of Service 287
- Configuring a Class Map 288
- Creating QoS Policies 290
- VoIP Traffic Configuration 294
- Configuring Telephony OUI 297
- Multicast 299
- Multicast Filtering 301
- Enabling IGMP Immediate Leave 303
- IGMP Filtering and Throttling 308
- Enabling IGMP Filtering 309
- Multicast VLAN Registration 313
- Switch Clustering 321
- Configuring Cluster Members 322
- UPnP Configuration 326
- Accessing the CLI 329
- Console Connection 329
- Telnet Connection 330
- Entering Commands 331
- Showing Commands 332
- Partial Keyword Lookup 333
- Using Command History 333
- Understanding Command Modes 333
- Exec Commands 334
- Configuration Commands 335
- Command Line Processing 336
- Command Groups 337
- General Commands 338
- Command Line Interface 340
- System Management Commands 344
- Device Designation Commands 345
- Banner Information Commands 346
- System Status Commands 355
- Frame Size Commands 361
- File Management Commands 362
- Line Commands 368
- Event Logging Commands 377
- SMTP Alert Commands 384
- Time Commands 387
- Switch Cluster Commands 401
- UPnP Commands 405
- Debug Commands 408
- SNMP Commands 409
- Authentication Commands 423
- Authentication Sequence 426
- RADIUS Client 428
- TACACS+ Client 432
- AAA Commands 437
- Web Server Commands 446
- Telnet Server Commands 449
- Secure Shell Commands 450
- 802.1X Port Authentication 459
- Management IP Filter Commands 468
- Port Security Commands 471
- DHCP Snooping Commands 486
- IP Source Guard Commands 494
- Access Control List Commands 498
- MAC ACLs 504
- ACL Information 509
- Interface Commands 510
- Link Aggregation Commands 524
- Power over Ethernet Commands 533
- Mirror Port Commands 539
- Rate Limit Commands 541
- Address Table Commands 542
- Spanning Tree Commands 546
- 548
- VLAN Commands 568
- Editing VLAN Groups 573
- Configuring VLAN Interfaces 575
- Displaying VLAN Information 581
- Configuring Voice VLANs 598
- LLDP Commands 605
- refresh-interval 610
- Class of Service Commands 627
- Quality of Service Commands 634
- Multicast Filtering Commands 643
- IGMP Query Commands (Layer 2) 648
- IP Interface Commands 666
- Software Features 671
- Management Features 672
- Standards 672
- Management Information Bases 673
- Software Specifications 674
- Appendix B: Troubleshooting 675
- Using System Logs 676
- Glossary 677
- Glossary-8 684
- Virtual LAN (VLAN) 684
- Numerics 685
- E112008/ST-R01 694
Produits connexes et manuels pour Mise en réseau Edge-Core ES3528M-PoE
(24 pages)
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels